Hadco Path Lights - Beacons

Hadco DWL1 Cast Brass Low Voltage Beacon Path Light

Finish: N Natural Bronze

HOUSING: Single-piece compression molded fiberglass reinforced polyester composite lower housing. Die cast brass upper housing. Fasteners are 300 series stainless steel. Two (2) 1/2" conduit inlets at bottom. Note: Watertight connectors and potting compound (by others) must be used to maintain a watertight seal at conduit entry points.

Finish: Natural Brass (N) is as-cast and tumble polished. Composite is pressure formed, molded-in color.
OPTICAL ASSEMBLY: Frosted borosilicate glass.

Lamping: 20W maximum T3 bi-pin lamp. Lamp is included with fixture. Lower wattage lamps are acceptable.
ELECTRICAL ASSEMBLY: Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1W wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
WARRANTY: Lifetime limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2008 Standards.

Height : 8 3/4" (222mm)
Width: 5" (127mm)

Hadco DWC1, DWCL1 Fiberglass Reinforced Polyester Composite Mini Beacon

Finish: A Black

DWCL1 Low Voltage
LAMPING: 20W maximum T3 bi-pin lamp. Lamp is included with fixture. Lower wattage lamps are acceptable.
ELECTRICAL ASSEMBLY: Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1W wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.

DWC1 Line Voltage with internal electronic transformer
LAMPING: 20W maximum T3 bi-pin lamp. Lamp is included with fixture. Lower wattage lamps are acceptable.
ELECTRICAL ASSEMBLY: Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. 120VAC, 60Hz input to step-down transformer. 12VAC output to fixture, for use with low voltage lamps. Fixture is pre-wired with 18 AWG black, white, and ground wires.

HOUSING: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Single-piece molded silicone gasket to prevent water, dust, and insect filtration. Fasteners are 300 series stainless steel. Two (2) 1/2" conduit inlets at bottom. Note: Watertight connectors and potting compound (by others) must be used to maintain a watertight seal at conduit entry points.

Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMBLY: Frosted borosilicate glass.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2008 Standards.

Height : 8 3/16" (224mm)
Width: 4 15/16" (126mm)

Hadco DWC2 Line Voltage Fiberglass Beacon

Finish: A Black

DWCL2 Low Voltage
LAMPING: 20W maximum T3 bi-pin lamp. Lamp is included with fixture. Lower wattage lamps are acceptable.
ELECTRICAL ASSEMBLY: Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1W wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.

DWC2 Line Voltage with internal electronic transformer
LAMPING: 20W maximum T3 bi-pin lamp. Lamp is included with fixture. Lower wattage lamps are acceptable.
ELECTRICAL ASSEMBLY: Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. Fixture is 12 volt. Internal electronic transformer has 120 volt input. Pre-wired with high temperature 18 AWG wire.

HOUSING: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Gasketing is silicone. Fasteners are 300 series stainless steel. Two (2) 1/2" conduit inlets at bottom. Note: Watertight connectors and potting compound (by others) must be used to maintain a watertight seal at conduit entry points.

Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMBLY: Ribbed clear acrylic.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2008 Standards.

Height : 7 3/8" (188mm)
Width: 5 5/16" (135mm)

Hadco 1010 Die-cast Aluminum, 1012 Injection Molded Polyester Resin Beacon Path Light

Finish: H Bronze

1010 Die-cast Aluminum

Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B117 specifications.
WARRANTY: Three-year limited warranty.

Height : 9 1/32" (229mm)
Width: 8 3/8" (213mm)

1012 Injection Molded Polyester Resin

Finish: Composite is textured, pressure formed, molded-in-color.
WARRANTY: Ten-year limited warranty.

Height : 12 1/4" (311mm)
Width: 8 3/8" (213mm)

HOUSING: Die-cast aluminum or injection molded polyester resin. Removable roof for easy relamping. Fasteners are 300 series stainless steel. Molded silicone gasket seals glass, top and bottom, and prevents moisture intrusion into the fixture.
NOTE: The base has two (2) 1/2" NPT conduit entrances for connection to the power source.
OPTICAL ASSEMBLY: Clear borosilicate glass refractor lens. Fully gasketed top and bottom.

Lamping: 100W maximum A19 lamp.
ELECTRICAL ASSEMBLY: Incandescent is medium base porcelain socket with nickel-plated screw shell and center contact.
BALLAST: Title 20 / Title 24 compliant where applicable. Factory wired and tested.
INSTALLATION & MOUNTING: VOLTAGE CAUTION: Some local interpretation of the NEC Section 210-6 only permit the use of 120 volt fixtures when they are mounted below 8'. Check with local authorities before specifying alternate voltages. Beacons are partially recessed. Potting compound must be used to seal the conduit wire entry. Lower housing may be recessed directly in the ground or in concrete.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2008 Standards.

*1 Add prefix VS to ordering logic
*2 Add prefix VM to ordering logic