Hadco IL336 Composite WellLyte Well Light Inground

IL336-AL - 12V IL336 Black

HD IL336-AL 20 watts Black

IG30H Rock Guard without Lens for IL336 Well light

The IL336 composite inground delivers the signature engineering and rugged construction that has made HADCO the leader in landscape lighting. Our patented lamp holder has integral fins to allow the height and angle of the lamp to be adjusted without any mechanical moving parts.

Available in Bulk Packs (25 Units)
PAR36 Inground Well Light (25 units)
PAR36 Inground Well Light with Lamp (25 units)

Housing: Single-piece PVC tube. Straight cut end allows flush ground mounting and an accessory lens guard or rock guard may be ordered separately, but is not required. Angled cut end requires the top 3" installed above ground for maximum vertical spot aiming with shielding being provided on three (3) sides. Patented Lamp Holder - Durable silicone rubber lamp holder has integral fins to allow the height and angle of the lamp to be adjusted without any mechanical moving parts. Fixture offers 360° lamp rotation and up to 45° off vertical aiming adjustability, restricted only by the cutoff of the housing.

Finish: A Black
Lamping: 50W maximum PAR36 screw terminal lamp. 20W PAR36 lamp is included with fixture. Lower wattage lamps are acceptable. Electrical Assembly: Double screw terminal socket. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
WARRANTY: Lifetime limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards.
Height: 8" (203mm)
Width: 5 5/8 (143mm)

Hadco I1.5 Small Incandescent Inground Landscape Light

The revolutionary i1.5 composite inground provides optimum performance in a small aperture light. Patented design elements including a hinged lens ring, potted factory seal, cool lens option and only 2 screws that do not require a torque wrench - the i1.5 reinforces HADCO's position as the leader in landscape lighting. Available in Incandescent, HID or LED.

Incandescent

HOUSING: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Separate compartments provide isolation between field wiring, optics, and ballast. Isolated, grade-mounted sealed wiring compartment with two (2) 3/4" threaded conduit inlets in bottom for feed-through wiring capabilities and supplied with gel-filled wire nuts. Cast cover to match lens ring with two captive stainless steel slotted Phillips machine screws for access. Potted factory seal with anti-wicking wiring between grade-level junction compartment and ballast compartment. Isolated ballast compartment with key-slotted cover. Half dome 360 degree field adjustable for glare control, constructed of natural cast Bronze (natural finish) or cast stainless steel (satin finish) to match lens ring. Lens ring is hinged with two captive stainless slotted Phillips machine screws for access to lamping compartment (tamper-resistant screws available upon request.) Lens ring and rockguard accessories are available in natural cast Bronze or cast stainless steel. Both options are designed to mount utilizing factory pre-drilled holes on lens ring with water channel to allow lens to stay free of dirt and contamination build-up.

Finish: Natural Bronze has satin Matte Finish, will age over time. Composite is pressure formed, molded-in color (black). Stainless Steel has satin Matte Finish.
OPTICAL ASSEMBLY: Aiming 15° either side of vertical and full 360° rotation. Angle degree marks for precise vertical aiming with tool-less aiming. Clear, slightly convexed, molded borosilicate glass, high impact, 3000 lb. live load rated, drive-over glass, with molded wrap around 100% silicone lens gasket. Optional lens assemblies include ice blue lens, linear or multi-directional spread lens. Ballast and optics are not sealed separately. Handle enables easy tool-less removal of optical assembly for hot aiming and re-lamping, simply press-fit back into place.

Lamping: 35W maximum MR16 bi-pin lamp. Lower wattage lamps are acceptable. Lamp is not included.
ELECTRICAL ASSEMBLY: Bi-pin socket type (GU5.3) with 250° C high temperature teflon coated wire leads.
CERTIFICATIONS: Manufactured to ISO 9001:2008 Standards. ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. ADA compliant when used in concrete and flush mounted with CPS15.
WARRANTY: Ten-year limited warranty.
IP RATING: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against continuous submersion in water tested to 1 meter (3.28 feet).

Height : 6" (153mm)
Width: 7 1/2" (191mm)
Depth: 9 3/4" (248mm)

Finish
SS Stainless steel (Matte Finish)
N Natural Bronze

Voltage
120 Volts
277 Volts

Hadco I1.5 Small HID Inground Landscape Light

HID

HOUSING: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Separate compartments provide isolation between field wiring, optics, and ballast. Isolated, grade-mounted sealed wiring compartment with two (2) 3/4" threaded conduit inlets in bottom for feed-through wiring capabilities and supplied with gel-filled wire nuts. Cast cover to match lens ring with two captive stainless steel slotted Phillips machine screws for access. Potted factory seal with anti-wicking wiring between grade-level junction compartment and ballast compartment. Isolated ballast compartment with key-slotted cover. Half dome 360 degree field adjustable for glare control, constructed of natural cast Bronze (natural finish) or cast stainless steel (satin finish) to match lens ring. Lens ring is hinged with two captive stainless slotted Phillips machine screws for access to lamping compartment (tamper-resistant screws available upon request.) Lens ring and rockguard accessories are available in natural cast Bronze or cast stainless steel. Both options are designed to mount utilizing factory pre-drilled holes on lens ring with water channel to allow lens to stay free of dirt and contamination build-up. Trim ring is natural cast Bronze or cast stainless steel.

Finish: Stainless Steel has satin Matte Finish. Natural Bronze has satin Matte Finish, will age over time. Composite is pressure formed, molded-in color (black).
OPTICAL ASSEMBLY: Aiming 15° either side of vertical and full 360° rotation. Angle degree marks for precise vertical aiming with tool-less aiming. Reflectors for T4 available for spot or flood beam pattern. Clear, slightly convexed, molded borosilicate glass, high impact, 3000 lb. live load rated, drive-over glass, with molded wrap around 100% silicone lens gasket. Optional lens assemblies include cool touch lens, (reducing lens temperatures by 15%), ice blue lens, linear or multi-directional spread lens. Ballast and optics are not sealed separately. Handle enables easy tool-less removal of optical assembly for hot aiming and re-lamping, simply press-fit back into place. High performance aluminum reflector for optimum symmetrical light output.

Lamping: 20W maximum MH GU6.5 base: T4. 39W maximum MH GU6.5 base: T4. Lamp is not included. See Ordering Guide for specific lamp types and wattages available.
ELECTRICAL ASSEMBLY: 4kv rated porcelain mini-can base. Ceramic twist and lock lamp base socket type (gu6.5) with 250° Celsius high temperature teflon coated wire leads. Key-slotted Ballast Assembly with Quick Disconnects mounted to cast aluminum bracket for easy maintenance.
BALLAST: All metal halide HID ballasts are e-Vision® universal electronic that automatically detect 120-277 volts, 50/60 Hz and are regulated with power factors better than 90% (HPF). Ballast provides +/- 5% lamp power regulation with +/- 10% input voltage regulation, sound rated "A", thermally protected, internally fused, output is short circuit protected, no PCBs. Ballasts are factory pre-wired and tested. Metal Halide ballasts are capable of starting at -4° F or -20° C, 39W max.
CERTIFICATIONS: ADA compliant when used in concrete and flush mounted with CPS15. Manufactured to ISO 9001:2008 Standards. ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations.
WARRANTY: Ten-year limited warranty.
IP RATING: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against continuous submersion in water tested to 1 meter (3.28 feet).

Height : 6" (153mm)
Width: 7 1/2" (191mm)
Depth: 9 3/4" (248mm)

Finish
SS Stainless steel (Matte Finish)
N Natural Bronze

Voltage
120 Volts
277 Volts

Hadco I1.5 Small LED Inground Landscape Light

LED

HOUSING: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Separate compartments provide isolation between field wiring, optics, and ballast. Isolated, grade-mounted sealed wiring compartment with two (2) 3/4" threaded conduit inlets in bottom for feed-through wiring capabilities and supplied with gel-filled wire nuts. Cast cover to match lens ring with two captive stainless steel slotted Phillips machine screws for access. Potted factory seal with anti-wicking wiring between grade-level junction compartment and ballast compartment. Isolated ballast compartment with key-slotted cover. Half dome 360 degree field adjustable for glare control, constructed of natural cast Bronze (natural finish) or cast stainless steel (satin finish) to match lens ring. Lens ring is hinged with two captive stainless slotted Phillips machine screws for access to lamping compartment (tamper-resistant screws available upon request.) Lens ring and rockguard accessories are available in natural cast Bronze or cast stainless steel. Both options are designed to mount utilizing factory pre-drilled holes on lens ring with water channel to allow lens to stay free of dirt and contamination build-up.

Finish: Stainless Steel has satin Matte Finish. Natural Bronze has satin Matte Finish, will age over time. Composite is pressure formed, molded-in color (black).

Lamping: 4,000K color temperature (CCT) or 3,000K. Approximately 50,000 hours of operational life (at 25 C ambient temperature and 70% lumen maintenance). >80 CRI.
OPTICAL ASSEMBLY: Clear, slightly convexed, molded borosilicate glass, high impact, 3000 lb. live load rated, drive-over glass, with molded wrap around 100% silicone lens gasket. Integral collimating spot (10°) optics. Integral collimating narrow flood (26°) optics. Integral collimating wide flood (38°) optics. Optional lens assemblies include ice blue lens, linear or multi-directional spread lens. Aiming 15° either side of vertical and full 360° rotation. Angle degree marks for precise vertical aiming with tool-less aiming. Handle enables easy tool-less removal of optical assembly for hot aiming and re-lamping, simply press-fit back into place.
ELECTRICAL ASSEMBLY: 12 total watts consumed Operating start temperature -30ºC (-22ºF). IP66 Compliant LED Driver. Black Magic Thermal Advantage™ Housing Driver 120 to 277 VAC input; 50-60Hz; auto-sensing.
CERTIFICATIONS: Manufactured to ISO 9001:2008 Standards. ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. ADA compliant when used in concrete and flush mounted with CPS15.
WARRANTY: Ten-year limited warranty.
IP RATING: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against continuous submersion in water tested to 1 meter (3.28 feet).

Height : 6" (153mm)
Width: 7 1/2" (191mm)
Depth: 9 3/4" (248mm)

Finish
SS Stainless steel (Matte Finish)
N Natural Bronze

Optics
FL Flood
SP Spot
NF Narrow Flood

CCT
W Warm 3000K
C Cool 4000K

* Electronic Driver: 120-277VAC 50/60 Hz auto-sensing

Hadco I2/I2G - Small Incandescent Line Voltage Inground Landscape Light

I2G-H PAR20 Bronze

I2-H In-Ground

Concrete Pour Kit for I2 and 12G

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Trim ring is a die-cast stainless steel. Trim ring is natural cast Bronze. Rock guard used for directional glare control made of compression molded polyester.

Finish: Composite is textured, pressure formed, molded-in-color.
H Bronze
N Natural Brass
SS Stainless steel (Matte Finish)
Optical Assembly: Clear convex, tempered soda-lime glass for high impact resistance. 2,200-pound live-load rated, standard walk-over lens.

Lamping: 100W maximum PAR30/R30 medium base lamp. 100W maximum PAR20/R20 medium base lamp. Lamp is not included. Lower wattage lamps are acceptable. (Note: PAR20/R20 and PAR30/R30 are not aimable.). Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards. ADA Compliant when flush mounted with CP2 or CPS2.
Height: 8 13/16" (224mm)
Width: 6 5/8" (169mm)

Hadco I2.5 LED Inground Landscape Light with Smart Select Driver: 120-277 vac 50/60 Hz Auto-Sensing INCLUDED

• (SP ) Spot
• (NF) Narrow Flood
• (FL ) Flood

LED (Light Emitting Diode) Included
Smart select driver: 120-277 vac 50/60 Hz auto-sensing

Description
The revolutionary i2.5 composite inground provides optimum performance in a small aperture light. Patented design elements including a hinged lens ring, potted factory seal, cool lens option and only 2 screws that do not require a torque wrench - the i2.5 reinforces HADCO's position as the leader in landscape lighting. Now available with LED !

Housing: Separate sealed compartments provide isolation between field wiring, optics, and ballast (CFL). Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Isolated, grade-mounted sealed wiring compartment with two (2) 3/4" threaded conduit inlets in bottom for feed-through wiring capabilities and supplied with gel-filled wire nuts. Cast cover to match trim ring with two captive stainless steel slotted Phillips machine screws for access. Potted factory seal with anti-wicking wiring between grade-level junction compartment and ballast compartment. Isolated ballast compartment with key-slotted, silicone- gasket cover. Rock guard made of cast brass (natural finish) or cast stainless steel (satin finish). Ring is factory pre-drilled for optional guard. Trim ring is natural cast Bronze or cast stainless steel. Lens ring is hinged with two captive stainless slotted Phillips machine screws for access to lamping compartment (tamper-resistant screws available upon request.) Half dome 360 degree field Adjustable for glare control, constructed of natural cast brass (natural finish) or cast stainless steel (satin finish) to match lens ring. Both options are designed to mount utilizing factory pre-drilled holes on lens ring with water channel to allow lens to stay free of dirt and contamination build-up.

Finish: Natural Brass has satin Matte Finish. Stainless Steel has satin Matte Finish.

Lamping: 5,000K color temperature (CCT) or 3,000K amber coated tempered glass lens. Approximately 50,000 hours of operational life (at 25 C ambient temperature and 70% lumen maintenance). >80 CRI.
Optical Assembly: Clear, flat, molded borosilicate glass, high impact, 3000 lb. live load rated, drive-over glass, with molded 100% silicone gasket, factory adheared. Optional lens assemblies include cool touch lens, reducing lens temperatures by 35%, ice blue lens, linear or multi-directional spread lens. Sealed optical chamber. Aiming 15° either side of vertical and full 360° rotation. Angle degree marks for precise vertical aiming with tool-less LOC-AIM^®. Handle enables easy tool-less removal of Optical Assembly for hot aiming and re-lamping, simply press-fit back into place. Electrical Assembly: Smart Select Electronic Driver 120 to277 VAC input; 50-60Hz; auto-sensing. Operating start temperature -40 C (-40 F) 17watts consumed (total fixture consumption)
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards. ADA compliant when used in concrete and flush mounted with CPS25.
WARRANTY: Ten-year limited warranty.
IP RATING: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against temporary immersion at a depth greater than 1 meter (3.28 feet).

Hadco I2.5 HID Inground Landscape Light

• (SP ) Spot
• (NF ) Narrow Flood
• (FL ) Flood
• (0) No Refl. Lamps

All HID Electronic Ballasts are Universal Voltage 120-277 VAC 50/60 HZ.

Fluorescent
BALLAST: All metal halide HID ballasts are Smart Select™ universal electronic that automatically detect 120-277 volts, 50/60 Hz and are regulated with power factors better than 90% (HPF). Ballast provides +/- 5% lamp power regulation with +/- 10% input voltage regulation, sound rated "A", thermally protected, internally fused, output is short circuit protected, no PCBs. Ballasts are factory pre-wired and tested. Metal Halide ballasts are capable of starting at -20° F or -30° C. 50W MH ballasts are capable of starting at 5° F or -15° C.

The revolutionary i2.5 composite inground provides optimum performance in a small aperture light. Patented design elements including a hinged lens ring, potted factory seal, cool lens option and only 2 screws that do not require a torque wrench - the i2.5 reinforces HADCO's position as the leader in landscape lighting.

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Separate sealed compartments provide isolation between field wiring, optics and ballast (MH and CFL). Isolated, grade-mounted sealed wiring compartment with two (2) 3/4" threaded conduit inlets in bottom for feed-through wiring capabilities and supplied with gel-filled wire nuts. Cast cover to match trim ring with two captive stainless steel slotted Phillips machine screws for access. Potted factory seal with anti-wicking wiring between grade-level junction compartment and ballast compartment. Isolated ballast compartment with key-slotted, silicone- gasket cover. Rock guard made of cast brass (natural finish) or cast stainless steel (satin finish). Ring is factory pre-drilled for optional guard. Trim ring is natural cast Bronze or cast stainless steel. Lens ring is hinged with two captive stainless slotted Phillips machine screws for access to lamping compartment (tamper-resistant screws available upon request.) Half dome 360 degree field Adjustable for glare control, constructed of natural cast brass (natural finish) or cast stainless steel (satin finish) to match lens ring. Both options are designed to mount utilizing factory pre-drilled holes on lens ring with water channel to allow lens to stay free of dirt and contamination build-up.

Finish: Composite is pressure formed, molded-in color. Natural Brass has satin Matte Finish. Stainless Steel has satin Matte Finish.
Optical Assembly: Clear, flat, molded borosilicate glass, high impact, 3000 lb. live load rated, drive-over glass, with molded 100% silicone gasket, factory adheared. Optional lens assemblies include cool touch lens, reducing lens temperatures by 35%, ice blue lens, linear or multi-directional spread lens. Sealed optical chamber. Aiming 15° either side of vertical and full 360° rotation. Angle degree marks for precise vertical aiming with tool-less LOC-AIM^®. Handle enables easy tool-less removal of Optical Assembly for hot aiming and re-lamping, simply press-fit back into place. High performance aluminum reflector for optimum symmetrical light output. Reflectors for T4 and T6 available for spot, narrow flood, or flood beam pattern. Reflectors for E17 available for spot or flood beam pattern.

Lamping: 70W maximum MH G8.5 base: T4. 70W maximum MH G12 base: T6. 70W maximum MH Medium base: E17. 70W maximum MH Medium base: PAR/R 20/30. Lamp is not included. See Ordering Guide for specific lamp types and wattages available. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact. Key-slotted Ballast Assembly with Quick Disconnects mounted to cast aluminum bracket for easy maintenance. Bi-pin socket type (G8.5) with 250° Celsius high temperature teflon coated wire leads. Bi-pin socket type (G12) for T6 lamps, with 250° Celsius high temperature teflon coated wire leads.
CERTIFICATIONS: Manufactured to ISO 9001: 2000 Standards. ADA compliant when used in concrete and flush mounted with CPS25. ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations.
WARRANTY: Ten-year limited warranty.
IP RATING: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against temporary immersion at a depth greater than 1 meter (3.28 feet).
Height: 15 3/4
Width: 7 1/2
Depth: 9 3/4

Hadco I2.5 Fluorescent Inground Landscape Light

Fluorescent
BALLAST: All Fluorescent ballasts are Smart Select™ universal electronic that automatically detect 120-277 volts, 50/60 Hz and are regulated with power factors better than 90% (HPF). Ballast provides +/- 5% lamp power regulation with +/- 10% input voltage regulation, sound rated "A", thermally protected, internally fused, output is short circuit protected, no PCBs. Ballast is factory pre-wired and tested. Ballast is capable of starting at 0° F or -18° C.

All CFL Electronic Ballasts are Universal Voltage 120-277 VAC 50/60 HZ and will operate 26w, 32w, or 42w lamps.
Universal CFL socket will accept 26w & 32w gx24q-3 and gx24q-4 lamps.

The revolutionary i2.5 composite inground provides optimum performance in a small aperture light. Patented design elements including a hinged lens ring, potted factory seal, cool lens option and only 2 screws that do not require a torque wrench - the i2.5 reinforces HADCO's position as the leader in landscape lighting.

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Separate sealed compartments provide isolation between field wiring, optics and ballast (MH and CFL). Isolated, grade-mounted sealed wiring compartment with two (2) 3/4" threaded conduit inlets in bottom for feed-through wiring capabilities and supplied with gel-filled wire nuts. Cast cover to match trim ring with two captive stainless steel slotted Phillips machine screws for access. Potted factory seal with anti-wicking wiring between grade-level junction compartment and ballast compartment. Isolated ballast compartment with key-slotted, silicone- gasket cover. Rock guard made of cast brass (natural finish) or cast stainless steel (satin finish). Ring is factory pre-drilled for optional guard. Trim ring is natural cast Bronze or cast stainless steel. Lens ring is hinged with two captive stainless slotted Phillips machine screws for access to lamping compartment (tamper-resistant screws available upon request.) Half dome 360 degree field adjustable for glare control, constructed of natural cast brass (natural finish) or cast stainless steel (satin finish) to match lens ring. Both options are designed to mount utilizing factory pre-drilled holes on lens ring with water channel to allow lens to stay free of dirt and contamination build-up.

Finish: Composite is pressure formed, molded-in color. Natural Brass has satin Matte Finish. Stainless Steel has satin Matte Finish.
Optical Assembly: Clear, flat, molded borosilicate glass, high impact, 3000 lb. live load rated, drive-over glass, with molded 100% silicone gasket, factory adheared. Optional lens assemblies include cool touch lens, reducing lens temperatures by 35%, ice blue lens, linear or multi-directional spread lens. Sealed optical chamber. Aiming 15° either side of vertical and full 360° rotation. Angle degree marks for precise vertical aiming with tool-less LOC-AIM^®. Handle enables easy tool-less removal of Optical Assembly for hot aiming and re-lamping, simply press-fit back into place. High performance aluminum reflector for optimum symmetrical light output. Reflectors for CFL are flood beam pattern.

Lamping: 26W CFL (GX24Q-3). 32W CFL (GX24Q-3). 42W CFL (GX24Q-4). Lamp is not included. Electrical Assembly: 42W Fluorescent socket is a GX24Q-4 base. (Will also accept 26W and 32W PLT lamps). Key-slotted Ballast Assembly with Quick Disconnects mounted to cast aluminum bracket for easy maintenance.
CERTIFICATIONS: Manufactured to ISO 9001: 2000 Standards. ADA compliant when used in concrete and flush mounted with CPS25. ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations.
WARRANTY: Ten-year limited warranty.
IP RATING: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against temporary immersion at a depth greater than 1 meter (3.28 feet).
Height: 15 3/4
Width: 7 1/2
Depth: 9 3/4

Hadco I3/I3G Inground Landscape Light

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Rock guard used for directional glare control made of compression molded polyester. Single-piece molded silicone U-channel gasket.

Finish: Composite is textured, pressure formed, molded-in-color.
Optical Assembly: Clear convex, tempered soda-lime glass for high impact resistance. 2,200-pound live-load rated, standard walk-over lens. Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern.

Lamping: 100W maximum PAR30/R30 or PAR38/R40 medium base lamp. Lamp is not included. Lower wattage lamps are acceptable. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards. ADA Compliant when used in concrete and flush mounted with CP3 or CPS3.
Height: 11 1/2" (295mm)
Width: 9 5/8" (244mm)

Hadco I3 Inground Landscape Light with Trim Ring

Finish

• (H) Bronze
• (N) Cast Bronze
• (SS ) Stainless Steel

Optics

• (SP ) Spot
• (NF) Narrow Flood
• (FL ) Flood
• (HA) Horizontal Asymmetric
• (H) Horizontal Symmetric
• (O) No Refl.*

Voltage

• 120V
• 208V
• 240V
• 277V

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Rock guard used for directional glare control made of compression molded polyester. Single-piece molded silicone U-channel gasket.

Finish: Composite is textured, pressure formed, molded-in-color.
Optical Assembly: Clear convex, tempered soda-lime glass for high impact resistance. 2,200-pound live-load rated, standard walk-over lens. Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern.

Lamping: 100W maximum PAR30/R30 or PAR38/R40 medium base lamp. Lamp is not included. Lower wattage lamps are acceptable. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards. ADA Compliant when used in concrete and flush mounted with CP3 or CPS3.
Height: 11 1/2" (295mm)
Width: 9 5/8" (244mm)

Hadco I3G Inground Landscape Light with Rock Guard

Finish

• (H) Bronze
• (N) Cast Bronze

Optics

• (SP ) Spot
• (NF) Narrow Flood
• (FL ) Flood
• (HA) Horizontal Asymmetric
• (H) Horizontal Symmetric
• (O) No Refl.*

Voltage

• 120V
• 208V
• 240V
• 277V

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Rock guard used for directional glare control made of compression molded polyester. Single-piece molded silicone U-channel gasket.

Finish: Composite is textured, pressure formed, molded-in-color.
Optical Assembly: Clear convex, tempered soda-lime glass for high impact resistance. 2,200-pound live-load rated, standard walk-over lens. Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern.

Lamping: 100W maximum PAR30/R30 or PAR38/R40 medium base lamp. Lamp is not included. Lower wattage lamps are acceptable. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards. ADA Compliant when used in concrete and flush mounted with CP3 or CPS3.
Height: 11 1/2" (295mm)
Width: 9 5/8" (244mm)

Hadco I3.5 150W PAR38 Inground Landscape Light

Hadco I3.5 LED Inground Landscape Light

i3.5 Composite Inground with Trim Ring

Finish: N Cast Bronze
Lamping: LED18 19W
Fixtures with PAR38 LED lamp will be shipped with fixture loose, not installed.
Lamps not sold separately.

Optics:
SP Spot
NF Narrow Flood
FL Flood

CCT: W Warm or C Cool

Features
• 120 Volt
• PAR38L LED
• 18 total watts

Housing
Single-piece compression molded, fiberglass reinforced polyester composite housing. Separate sealed compartments. Potted factory seal with antiwicking wiring. Hinged lens ring with captive lens and fasteners. Only two fasteners required to secure lens ring. UL Listed silicone-filled wire nuts provided–no encapsulant required.

Trim Ring
Natural cast bronze. Secured with stainless steel screws (supplied standard).

Rock Guard Natural cast bronze. Secured with stainless steel screws (sold separately).

Half Dome
Field adjustable for directional glare control. Natural cast bronze. Secured with stainless steel screws (sold separately).

Lens
Clear convex, tempered borosilicate for highimpact resistance. 3,000 lb live-load rated, drive-over.

LED Lamp
• 25,000 hours life (no mercury).
• 19W lamp with 15° or 25º beam spread (only sold integral to i3.5 fixture).
• Color temp. (CCT): warm white (3,000K nominal).

Socket
Incandescent, PAR38 and MH E-17: 4kv rated medium base porcelain socket.

Optics
Available with spot, narrow flood or flood beam pattern. EnduraLED lamps: spot or flood beam pattern.

Gasket
Single-piece wrap around molded 100% silicone for lens assembly. Gasket for J-box cover is single-piece die-cut neoprene.

LED Module
4,000K CCT or 3,000K CCT. Approx. 50,000 hours of operational life (at 25 Cambiant temperature and 70% lumen maintenance). >80CRI.

Aiming
15° either side of vertical and full 360° rotation. Angle degree marks for precise vertical aiming with tool-less aiming.

ADA Compliant
Compliant when used in concrete and Flush Mounted with CPS35.

Electrical
LED module is a key-slotted ballast assembly with quick disconnects mounted to cast aluminum bracket for easy maintenance. e-Vision electronic ballasts automatically detect 120-277 volts, 50/60 Hz, HPF. Ballasts provide ± 5% lamp power regulation with ± 10% input voltage regulation. Incandescent (MR16) - utilizes stepdown transformer.

IP Rating
IP66/68 to 1M (3.28FT): Dust-tight and dual rated – sealed against direct jets of water and against continuous immersion up to a depth of 1 meter (3.28 feet).

ETL and cETL listed.

Hadco I3.5 HID Inground Landscape Light

Hadco I4/I4G Inground Landscape Light

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Rock guard used for directional glare control made of compression molded polyester. Single-piece molded silicone U-channel gasket.

Finish: Composite is textured, pressure formed, molded-in-color.
Optical Assembly: 2,600-pound live-load rated, standard walk-over lens. Clear convex, tempered soda-lime glass for high impact resistance. Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern.

Lamping: 150W maximum PAR38/R40 incandescent lamp. Lamp is not included. Lower wattage lamps are acceptable. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards. ADA Compliant when used in concrete and flush mounted with CP4 or CPS4.
Height: 14" (354mm)
Width: 12 1/4" (310mm)

Hadco I4 Inground Landscape Light with Trim Ring

Finish

• (H) Bronze
• (N) Cast Bronze
• (SS ) Stainless Steel

Optics

• (SP ) Spot
• (NF) Narrow Flood
• (FL ) Flood
• (HA) Horizontal Asymmetric
• (H) Horizontal Symmetric
• (O) No Refl.*

Voltage

• 120V
• 208V
• 240V
• 277V

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Rock guard used for directional glare control made of compression molded polyester. Single-piece molded silicone U-channel gasket.

Finish: Composite is textured, pressure formed, molded-in-color.
Optical Assembly: 2,600-pound live-load rated, standard walk-over lens. Clear convex, tempered soda-lime glass for high impact resistance. Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern.

Lamping: 150W maximum PAR38/R40 incandescent lamp. Lamp is not included. Lower wattage lamps are acceptable. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards. ADA Compliant when used in concrete and flush mounted with CP4 or CPS4.
Height: 14" (354mm)
Width: 12 1/4" (310mm)

Hadco I4G Inground Landscape Light with Rock Guard

Finish

• (H) Bronze
• (N) Cast Bronze

Optics

• (SP ) Spot
• (NF) Narrow Flood
• (FL ) Flood
• (HA) Horizontal Asymmetric
• (H) Horizontal Symmetric
• (O) No Refl.*

Voltage

• 120V
• 208V
• 240V
• 277V

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Rock guard used for directional glare control made of compression molded polyester. Single-piece molded silicone U-channel gasket.

Finish: Composite is textured, pressure formed, molded-in-color.
Optical Assembly: 2,600-pound live-load rated, standard walk-over lens. Clear convex, tempered soda-lime glass for high impact resistance. Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern.

Lamping: 150W maximum PAR38/R40 incandescent lamp. Lamp is not included. Lower wattage lamps are acceptable. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards. ADA Compliant when used in concrete and flush mounted with CP4 or CPS4.
Height: 14" (354mm)
Width: 12 1/4" (310mm)

Hadco IF218/IF226/IF232 Small Fluorescent Line Voltage Inground Landscape Lighting

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Rock guard used for directional glare control made of compression molded polyester.

Finish: Composite is textured, pressure formed, molded-in-color.
Optical Assembly: Clear convex, tempered soda-lime glass for high impact resistance. 2,200-pound live-load rated, standard walk-over lens.

Lamping: Lamp is not included. Lower wattage lamps are acceptable. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact. 26W Fluorescent socket is a GX24Q-3 base. 32W Fluorescent socket is a GX24Q-3 base. 18W Fluorescent is a GX24q-2 socket.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: UL Listed to U.S. safety standards for wet locations. cUL Listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards. ADA Compliant when flush mounted with CP2 or CPS2.
Height: 8 1/4" (210mm)
Width: 6 5/8" (169mm)

Hadco IL116/IL136 Composite Low Voltage Inground Landscape Lighting

IL116G-H - 12V with Rock Guard Bronze

IL116-H - Inground Bronze

IL116
Lamping: 75W maximum MR16 bi-pin lamp. Covered MR16 are recommended to protect lamps inner capsule. Lower wattage lamps are acceptable.

IL136
Lamping: 75W maximum PAR 36/AR11 screw terminal lamp. Lower wattage lamps are acceptable. 

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester.

Finish: Composite is textured, pressure formed, molded-in-color.
Optical Assembly: Clear convex, tempered soda-lime glass for high impact resistance. 2,200-pound live-load rated, standard walk-over lens. Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern. Electrical Assembly: Bi-pin socket type (GU5.3) with 250° C high temperature teflon coated wire leads. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards. ADA Compliant when flush mounted with CP2 or CPS2.
Height: 8 7/16" (214mm)
Width: 6 5/8" (169mm)

Hadco IT216, IT236 IT2 Small WelLyte Line Voltage Inground Landscaping Light

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Trim ring is a die-cast stainless steel. Trim ring is natural cast Bronze. Rock guard used for directional glare control made of compression molded polyester.

Finish: Composite is textured, pressure formed, molded-in-color.
Optical Assembly: Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern. Clear convex, tempered soda-lime glass for high impact resistance. 2,200-pound live-load rated, standard walk-over lens.

Lamping: 75W maximum PAR 36/AR11 screw terminal lamp. 75W maximum MR16 bi-pin lamp. Lamp is not included. Lower wattage lamps are acceptable. (Note: PAR20/R20 and PAR30/R30 are not aimable.). Electrical Assembly: Bi-pin socket type (GU5.3) with 250° C high temperature teflon coated wire leads. Double screw terminal socket. Step-down transformer reduces line voltage to 12 volts.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards. ADA Compliant when flush mounted with CP2 or CPS2.
Height: 8 13/16" (224mm)
Width: 6 5/8" (169mm)

Hadco IUL516 Ultem Micro Inground 12v Low Voltage Composite Inground Landscaping Light

Also available in Bulk Packs (25 Units)
IUL516-HBAB25 MR16 Inground with Lamp (25 Units)
IUL516-HBULK25 MR16 Inground Fixture Bulk Pack (25 units)

Housing: One-piece injection molded ULTEM^® High Performance Polymer composite. Lens ring is a Single-piece injection molded ULTEM^® High Performance Polymer with gasketed lens. Twist-off operation for ease of maintenance.

Finish: Composite is textured, pressure formed, molded-in-color.
Optical Assembly: Clear convex, tempered glass furnished with silicone O-ring for watertight seal.

Lamping: 35W maximum MR16 bi-pin lamp. Lower wattage lamps are acceptable. Covered MR16 are recommended to protect lamps inner capsule. Electrical Assembly: Bi-pin socket type (GU5.3) with 250° C high temperature teflon coated wire leads. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
ACCESSORIES: IBL16 Ice blue Lens. ISL16 Spread Lens. IAS16 Linear Spread Lens. ICG16 - Internal snap on Honeycomb louver (Lamp MR16). CP5 - Concrete Pour Kit.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards.
Height: 4 3/8" (111mm)
Width: 4 1/8" (105mm)

Hadco FlexScape LED IL9 Low-Voltage LED Inground Landscape Light

The all-in-one solution for landscape lighting
Imagine the convenience and cost savings of having different light levels and a variety of beam patterns, all within a single LED luminaire. Introducing FlexScape, a new family of innovative accent and inground landscape luminaires for commercial and residential applications.

One fixture. Multiple light levels and beam patterns.
Every FlexScape luminaire provides countless lighting outcomes to choose from. As a result, you'll also enjoy better flexibility in the field, meaning easy adjustments during installation or down the road, should the landscape or lighting needs change. In addition, its LUXEON LED technology ensures outstanding energy savings and service life.

Exclusive customizing capabilities.
Both FlexScape inground and accent luminaires have built-in flexibility. Choose from four light outputs between 111 and 710 lumens, as well as beam patterns ranging from narrow (15°) to wide flood (60°). With different lighting outcomes, FlexScape lets you custom-design the most suitable landscape luminaire for the job, while saving time and money.

The LED Inground model opens new horizons for low-voltage landscape lighting. It is designed for optimal LED performance and superior flexibility.

The luminaire creates visual interest for, pathways, walls, columns and foliage. Its rugged housing installs directly into the soil. In addition to low-energy outdoor lighting, it features convenient on site beam adjustability. This all-weather luminaire comes with 100% molded silicone gaskets.

Hadco FlexScape LED Landscape Lights >

1. Excavate soil for fixture placement and conduit runs. Allow a minimum of 3" around and under housing for drainage material.

2. Remove the screws from the glass/ gasket assembly and wiring compartment cover. Connect conduit fittings to housing conduit entries utilizing a thread sealant, and tighten to 40 ft-lbs. Max. DO NOT REMOVE the moisture absorbing desi-pak from inside the fixture.

3. Connect 120V leads in wiring compartment to supply wires. Make ground connection. The contractor must pull ground wire or make a ground connection to the metal conduit system.

4. Conduit entries must be potted to prevent water entry (3M 4442 GELA supplied with I3 and I4). Replace the wiring compartment cover.

5. Install the ballast tray. Plug lamping module into quick connect, if applicable.

6. Install the correct lamp. DO NOT EXCEED the maximum wattage marked on the fixture.

7. Clean gasket seating surfaces. Screw holes can be blown clear or cleared with a #10-24 tap. Insert screws through lid and tighten using an alternating torque sequence to 20 (min.) 30 (max.) inch-lbs.

8. Fixture housing should be surrounded by a 3" (minimum) layer of sand or gravel to ensure drainage. Materials such as vermiculite and bark are for ground cover only. Full depths of these may cause overheating. In concrete pour cases, the housing is placed on a 4" (minimum) bed of gravel, with soil below. Do not install fixtures where water collects arid stands for any Length of time.